Installing bike grips

Carpet tape is a little thicker that double-sided tape but you will hardly know the difference. Gently slide each grip onto your shafts, making sure that they are down the shaft as far as they can go. To install a grip, you need at least 1 wrap of grip tape to match the stated size of the grip. This means there is one layer of tape that goes around and does not overlap the grip, regardless of the size of the grip. This single-coated, masking tape is used for building up grip sizes.

Each wrap adds about. I use a thin screwdriver or spoke and a spraybottle with soapy water. Pry, spray, work it around it a bit and it usually twists right off. They are worth the money.

I have large hands they offer different sizes and the grip is perfect. Bar ends will extend your handlebar, and allow you to move your hands more forward, this lowers the center of gravity at the same time.

Pull the tape tight -- you want a lot of tension for a tight, waterproof grip. Leave about half the tape hanging off the bottom of the bar on the first pass, wrapping times as you work up. Move up the bar, overlapping slightly for wraps. Then push the cap into the exposed wrap, sucking it into the inside of the handlebar so that the cap holds the bottom of the tape in place.

Repeat on both sides. Work slowly, overlapping about a quarter of the tape with every turn, as you move up the bar. If there is adhesive in tape, it is often covered. Pull off the covering now and slowly, tightly wrap the tape up and around the bar.

You may have to pull and work the tape multiple times, making sure there are no gaps. It is often best to test the tension of the tape before starting. Give a good tug to feel how tightly you can pull on the tape without ripping it.

To avoid gaps where the bar bends, you may have to overlap a bit more. The top of the handlebars, the flat part, need to be wrapped in reverse.

As you finish the bottom of the bars, get as close to the levers as you can. Then skip over a small area where the bars bend and just start wrapping the top of the bars. Reverse your wrapping direction for the top of the bars. This will be easy if you skip past the lever covering, as outlined above. Most riders will rotate their wrists back on the top bar, potentially unraveling the tape.

This is why you change directions when getting to the top bar: [12] X Research source The right side should be wrapped counter-clockwise. The left side should be wrapped clockwise. Cut the tape at your desired length and finish wrapping. You can "overwrap" it, then use a pen to mark the points you want to cut it.

Then simply follow this line with scissors for a clean, professional tape-up. Add some wraps of electrical tape to hold the wrap in place. At the very end of the tape, use some "finishing tape," to secure the wrap in place. Add enough that it cannot be easily unwound, usually using " on the tape and " on the bike frame.

For a better hold, use a lit match to melt the tapes together in a few places, "welding" your handlebar tape on. No, that won't work. Hairspray works because it eventually evaporates. Gel will just stay there and make your grip slip away from your handlebar. Not Helpful 1 Helpful Now that I know how to put them on - where can I buy replacement grips for a 16 inch bicycle? Alonzo V. Every Walmart superstore sells them with many different options. Or find your nearest bicycle store.

Not Helpful 0 Helpful 2. Alcohol can help with installing new grips, as it decreases friction and dries quickly. However, I would only recommend pure rubbing alcohol, not a substance containing it, as the chemicals may damage the grips or bars. Not Helpful 0 Helpful 0. Different bikes may have different feels, effects, functionality with the same exact grip. Include your email address to get a message when this question is answered. By using this service, some information may be shared with YouTube.

Using oil or soapy water or anything like that to apply grips will simply make your grip slide around on the bar for the rest of the time you own the bike. Helpful 3 Not Helpful 0. Helpful 1 Not Helpful 0. Be very careful with blades around your bike frame, especially if the frame is carbon fiber.

Small nicks and cuts can compromise the frame's stability in the case of a crash. Helpful 1 Not Helpful 2. You Might Also Like How to. If you've already registered with us, sign in here. Install New Grips And installing the new grips is even easier! Register Create your Pure Cycles account to receive promotional news and access to a faster checkout process.

First Name. Last Name. Email Address. Have an account? Sign in Email Address. Forgot password? We will send you an email with instructions to reset your password. I'm new here Create your Pure Cycles account to receive promotional news and access to a faster checkout process.